TURBINE OIL PURIFICATION SYSTEM & FILTER MACHINE · 600–18,000 LPH

Turbine Oil Purifier & Purification System: Break Emulsions ≤ 100 ppm, Hold NAS 5 & Cut Varnish MPC ≤ 8

Engineered for steam turbines, combined-cycle gas turbines, hydro governor stations, and centrifugal turbo-compressors running ISO VG 32 / 46 turbine oil — compare Heating-Free Coalescing Purifiers (WJJ, ≤ 100 ppm), Varnish & Water Removal Units (WVDJ, MPC ≤ 8), and Single-Stage Vacuum Filter Machines (WZJC, ≤ 50–100 ppm) built for 380V–440V (50Hz/60Hz) and Ex d IIC sites.

Turbine Oil Purification by Contamination Mode & Field Duty

Gland-seal steam ingress in a condensing steam turbine, bearing-pad varnish precipitation in a gas turbine or centrifugal compressor, and trace dissolved gas in a circulation reservoir do not respond to the same filter medium. Match youroil lab profile (ppm, NAS, MPC), viscosity (32–100 cSt), and power constraintsacross our three turbine oil purification lines below.

Steam Seal Leaks · Free & Emulsified Water

Heating-Free Bulk Dewatering & Sub-Micron Cleanliness

Recommended: WJJ Coalescing Balanced-Charge
For steam turbines, CCGT units, and lube stations facing up to < 10% water ingress — cuts moisture ≤ 100 ppm and holds < NAS 5 at 0.9–7.6 kW with zero thermal stress.

High MPC Varnish · Servo Sticking & Pad Temp Spikes

Soluble Varnish Adsorption + Simultaneous Water Control

Recommended: WVDJ (3-in-1 Varnish + Coalescing)
Strips dissolved varnish (MPC ≤ 8), 0.02 μm suspended sludge (NAS ≤ 6), and moisture ≤ 100 ppm at 20 L/min without stripping amine antioxidants.

Dissolved Moisture · Air & Gas Stripping

Vacuum Flash Dehydration & Multi-Stage Solids Filtering

Recommended: WZJC Single-Stage Vacuum (1,800–12,000 LPH)
Uses −0.06 to −0.09 MPa vacuum and ≤ 2 W/cm² heaters (≤ 80°C) to drive moisture down to ≤ 50–100 ppm, strip entrained air, and filter solids to ≤ 3 μm.

CORE TURBINE WATER & PARTICLE WORKHORSE · WJJ SERIES

WJJ Heating-Free Coalescing & Balanced-Charge Turbine Oil Purifier

Designed specifically for steam and gas turbine lubricating oils (32–100 cSt, up to ≤ 220 cSt), the WJJ combines 100% cellulose-free synthetic coalescing-separation stages with 0.1 μm balanced-charge particle agglomeration. Positive and negative charging chambers force sub-micron wear particles and oxidation sludge to collide into filterable clusters while coalescer cartridges strip free and emulsified water down to ≤ 100 ppm and discharge it via an automatic water drain.

Available across WJJ-10 through WJJ-300 (600 to 18,000 LPH / 10 to 300 L/min), the unit operates at ambient lube temperature (≤ 80°C, zero electric heaters) at just 0.9–7.6 kW, sustaining NAS 3–7 (< NAS 5 long-term) over 500+ hours of unattended kidney-loop duty.

Typical Application Scenarios

Target Equipment & Buyers: Steam turbines with gland-seal condensation or cooler water leaks, CCGT combined-cycle lube reservoirs (6–20+ m³), petrochemical centrifugal compressor oil consoles, and large industrial fans/pumps.

Ideal Operating Condition: Heavy free or emulsified water contamination (inlet moisture < 10%) where rapid bulk dewatering outperforms vacuum evaporation and zero heating protects additive life.

Limitations & Operating Boundaries

Soluble Varnish Boundary: Balanced charge coalesces suspended soft sludge physically, but cannot chemically adsorb hot dissolved varnish precursors — choose WVDJ when MPC or bearing pad temperatures rise.

Demulsibility & Gas Limit: Requires oil with functional water-separating properties (not degraded tight emulsions), and does not pull sub-50 ppm dissolved gas like WZJC vacuum dehydration.

3-IN-1 VARNISH, WATER & SLUDGE REMOVAL · WVDJ SERIES

WVDJ Turbine Oil Varnish & Water Removal Purification System

Built for hot-running gas turbines and steam/compressor trains where both soluble varnish and trace-to-moderate water threaten reliability, the WVDJ (WVDJ-20 & Ex-proof WVDJ-20-IIC) integrates three stages at 20 L/min (1,200 LPH, 1.2 kW): a circular high-voltage electrostatic collector (0.02 μm suspended sludge), imported Dow ion-exchange resin (adsorbing soluble varnish down to MPC ≤ 8), and synthetic coalescing-separation dewatering (≤ 100 ppm).

Unlike standard mechanical filtration or thermal vacuum dehydration, WVDJ selectively captures polar oxidation degradation products while preserving hindered-phenol and aromatic-amine antioxidants, restoring clean oil solvency to reverse-dissolve baked deposits from thrust bearings and hydraulic servo valves online (NAS ≤ 6).

Typical Application Scenarios

Target Equipment & Buyers: Gas turbine generators, newly commissioned turbine trains, steam-driven syngas/ethylene/air-separation centrifugal compressors (ISO VG 32/46), and Ex-zone process plants (WVDJ-20-IIC, IP56).

When WVDJ Beats Dry-Only VRU: Mandatory whenever moisture exceeds 100 ppm (up to < 10%) or settled tank-bottom water could trip electrostatic leakage interlocks on dry-only units like our WVD Series.

Limitations & Operating Boundaries

Bulk Water Floods: Handles < 10% inlet moisture at 20 L/min; if a steam turbine suffers severe seal flooding on a 10–30 m³ tank, pre-dewater with WJJ (up to 300 L/min) so coalescing load does not overwhelm resin life.

Dry-Only Alternative: If your lab report and bottom-drain sample confirm strictly dry oil (≤ 100 ppm, zero free water), explore our dedicated Varnish Removal Units.

VACUUM DEHYDRATION & DEGASSING · WZJC SERIES

WZJC Single-Stage Vacuum Turbine Oil Filter Machine (Moisture & Gas Removal)

When specifications explicitly call for vacuum degassing and sub-100 ppm dissolved-moisture extraction across petroleum lubricating oils up to ≤ 220 cSt, the WZJC (WZJC-2KY through WZJC-12KY, 1,800–12,000 LPH / 30–200 L/min) flashes off free water, dissolved moisture, and entrained air inside a coarse-atomization chamber at −0.06 to −0.09 MPa vacuum and ~60°C (≤ 80°C max) controlled heating.

Low surface heat-flux heaters (≤ 2 W/cm²), liquid-expansion thermostats, and multi-stage pleated ≤ 3 μm mechanical elements (or optional filter-press paper) restore turbine and hydraulic oil down to ≤ 50–100 ppm water and NAS Class 7 without localized oil scorching.

Typical Application Scenarios

Target Equipment & Buyers: Power plant auxiliary turbines, governor hydraulics, marine gear/turbine reservoirs, and multi-purpose industrial lube stations requiring both vacuum air/gas stripping and low-ppm dehydration (≤ 50–100 ppm).

Modular Frame & Optional Add-Ons: Available in KY (open mobile), BF (enclosed stationary), BY (enclosed mobile), and KF (open stationary) builds, with optional coalescing stages, online moisture/particle sensors, or WJZ vacuum + balanced-charge upgrade for NAS 5 cleanliness.

Limitations & Operating Boundaries

No Varnish or Gel Removal: Conventional mechanical elements (≥ 3 μm) and vacuum evaporation cannot remove sub-micron oxidation gels (0.02–0.5 μm) or dissolved varnish; heavy sludge can also clog pleated cartridges rapidly.

Connected Heater Load & Bulk Water: Requires 21–81 kW connected electrical power; for high free-water steam leaks without heating power overhead, choose WJJ Coalescing instead.

PURIFICATION SYSTEM SIZING & ELECTRICAL SPECS

Turbine Oil Purification System Specifications (LPH), Power & Ex-Proof Builds

Compare our primary heating-free WJJ Coalescing & Balanced-Charge turbine oil purifier frames below (verified against factory datasheets from 600 to 18,000 LPH), alongside companion WVDJ Varnish + Water and WZJC Vacuum specifications.

Specification (WJJ Series) WJJ-30 WJJ-50 WJJ-100 (Core Utility Size) WJJ-200 WJJ-300
Flow Capacity (LPH / L/min) 1,800 LPH (30 L/min) 3,000 LPH (50 L/min) 6,000 LPH (100 L/min) 12,000 LPH (200 L/min) 18,000 LPH (300 L/min)
Total Power (Heating-Free) 0.9 kW 1.8 kW 3.5 kW 6.5 kW 7.6 kW
Outlet Water / Cleanliness ≤ 100 ppm moisture (from < 10% inlet water) · NAS Class 3–7 (sustains < NAS 5) · 0.1 μm balanced-charge precision
Working Temp / Pressure ≤ 80°C ambient lube loop (zero heaters) · 0.05–0.4 MPa working pressure · Automatic water drain
Dimensions (L × W × H mm) 1,820 × 1,000 × 1,650 1,855 × 1,000 × 1,650 1,890 × 1,000 × 1,675 2,335 × 1,180 × 1,780 2,335 × 1,200 × 1,900
Reference Weight 530 kg 560 kg 780 kg 1,000 kg 1,150 kg
Typical Plant Fit Auxiliary lube skids (also WJJ-10 at 600 LPH / 500 kg) Medium turbine & compressor reservoirs 6–20 m³ steam & CCGT turbine lube stations (also WJJ-80 / 150) Large utility steam turbines & central oil stations High-flow central power-block reservoirs

Companion WVDJ Varnish & WZJC Vacuum Specifications

WVDJ Series (WVDJ-20 / Ex-proof WVDJ-20-IIC): 1,200 LPH (20 L/min), 1.2 kW, 20–80°C, −0.06 MPa inlet / 0.4 MPa outlet, L 2,175 × W 915 × H 1,875 mm, 550 kg (IP55) / 650 kg (IP56, Ex d IIC) for MPC ≤ 8, NAS ≤ 6, and ≤ 100 ppm water.
WZJC Vacuum Series (2KY–12KY): 1,800 / 3,000 / 6,000 / 9,000 / 12,000 LPH (30–200 L/min), 21–81 kW total power, −0.06 to −0.09 MPa, ≤ 3 μm (NAS 7), ≤ 50–100 ppm water.

Custom 3-Phase Power Grids, Hazardous Zones & Mobility

Every control cabinet and motor is factory-built to match plant auxiliary supply — supporting 380V 50Hz / 60Hz, 400V 50Hz, 415V 50Hz, 440V/220V 60Hz, and 480V 60Hz grids. Available with CE compliance, Ex d IIC / IP56 explosion-proof housings for gas-turbine and petrochemical compressor decks, open/enclosed mobile carts (KY/BF/BY/KF), and optional online moisture/particle monitors.

MANUFACTURING SCALE & WORKFLOW FIT

Match the Right Turbine Oil Purification Process to Your Plant Team

Thermal power steam turbines, combined-cycle gas turbines, hydro governor stations, and petrochemical turbo-compressors fail from very different contamination pathways. Every VIFLUTER turbine oil purifier completes full pressure leak testing, dielectric interlock verification, and flow calibration prior to shipment.

Steam Power Plants CCGT Gas Turbines Hydro Governor Oils Turbo-Compressors

Verified Factory Scale Since 2009

Built in our 50,000 m² manufacturing base with 800 skids/year capacity and 6,000+ purification systems deployed across 2,000+ power and process plants.

Proven on rotating machinery operated by China Guodian, CNOOC, Sinopec, PetroChina, Linde Gas, and Wanhua Chemical.

Configured to Fluid State & Site Safety Rules

Pair WJJ (zero-heat bulk water & NAS ≤ 5 control), WVDJ (soluble varnish MPC ≤ 8 + water ≤ 100 ppm), or WZJC (vacuum gas/water stripping) — wired for 380V–480V and Ex d IIC zones.

Treating strictly dry varnish (≤ 100 ppm water) or EHC phosphate-ester fluid? Explore our Varnish Removal Units (WVD) or WJZ-K8 EHC Purifiers.

Send Oil Grade (32#/46#), Tank Volume & Lab Report
Receive a kidney-loop LPH sizing sheet, WJJ / WVDJ / WZJC selection, and FOB/CIF quote.
Consult a Process Engineer →
VERIFIED FIELD CASES & LAB BENCHMARKS

Proven Turbine Oil Purification Results Across Power & Process Plants

Inspect documented turbine and rotating-machinery deployments verified against factory engineering logs and third-party lab reports — cutting free/emulsified moisture below 100 ppm, stabilizing NAS ≤ 5–6, and dropping bearing pad temperatures & MPC varnish potential.

Two VIFLUTER WJJ coalescing balanced charge turbine oil purifiers operating on a GE gas turbine lube reservoir
GAS TURBINE COGENERATION · WJJ-100

China Guodian GE Gas Turbine: 617 ppm & NAS ≥ 11 Cleared Before Startup

A 20 m³ (20,000 L) GE PG61111FA gas-steam combined-cycle lube system running Total ISO VG 32 turbine oil failed pre-commissioning cleanliness and water limits (617 ppm water, NAS ≥ 11). Two heating-free WJJ-100 units restored moisture < 100 ppm and NAS ≤ 5 without heater stress.

Petrochemical cracked gas compressor electrostatic and resin varnish removal lowering bearing pad temperature from 115 C to 89 C online
TURBO-COMPRESSOR & GAS TURBINE VARNISH

Cracked Gas Compressor & Offshore Turbine: 115°C Pad Temp Down to 89°C

Combining circular electrostatic adsorption with Dow ion-exchange resin reduced petrochemical cracked-gas compressor bearing temperature from 115°C to 89°C online. On a Solar T60 offshore gas turbine (1,800 L Regal R&O 46), third-party testing verified MPC ΔE 31.5 → 4.4 and NAS 13 → 5, stabilizing control-valve pressure.

VIFLUTER vacuum dehydration turbine oil filter machine deployed at CITIC Pacific Power Generation plant
POWER PLANT DEHYDRATION · WZJC / WJJ

CITIC Pacific Power & 75 MW Steam Turbine: Gland Water > 2% Cut ≤ 100 ppm

Across power-plant continuous dehydration duties, WZJC Single-Stage Vacuum removes 100% free water and up to 95% dissolved water/gas (≤ 50–100 ppm, ≤ 3 μm). On heavy steam-seal leaks (> 2% chronic water in a 75 MW condensing turbine running VG 46), WJJ-100 held moisture ≤ 100 ppm and NAS 5–6.

Verified Turbine Oil Conditioning Benchmarks (ASTM D6304 / NAS 1638 / ASTM D7843 Lab Standards):
Outlet Water (WJJ / WVDJ / WZJC)
≤ 50–100 ppm
Particulate Cleanliness
NAS 5–6 (3–5 WJJ)
Varnish Potential (MPC ΔE)
≤ 8 (Lab 1.1–4.5)
Amine & Phenol Additives
100% Preserved
BUYER'S ENGINEERING GUIDE

3 Engineering Rules Before Specifying a Turbine Oil Purifier

Turbine lubrication failures rarely come from a single contaminant. Misapplying a mechanical cartridge, a centrifugal separator, or a heater-type vacuum dehydrator onto dissolved varnish — or feeding wet tank-bottom oil into a dry electrostatic unit — wastes capex. Apply these three engineering boundaries before ordering.

01
Coalescing vs. Vacuum

Match Water Load & Flow Rate to Reservoir Size

For free & emulsified water (< 10% inlet) from steam-seal leaks, WJJ Coalescing drains water fast at ambient temperature (0.9–7.6 kW) with zero moving centrifuge wear parts. Reserve WZJC Vacuum (−0.06 to −0.09 MPa) for ≤ 50 ppm dissolved moisture and air stripping. Field sizing benchmark: pair WJJ-50 / WJJ-100 (3,000–6,000 LPH) on 6–20 m³ turbine tanks, or WVDJ-20 (1,200 LPH) for continuous kidney-loop varnish control up to 80,000 L.

Heating-Free Protection6–20 m³ Field Sizing
02
MPC ≤ 8 & RULER

Strip Soluble Varnish Without Depleting Amines

At 40–60°C operating lube temperatures, varnish precursors stay fully dissolved, passing right through 3–10 μm mechanical filters, centrifuges, and standard vacuum purifiers — often masking high MPC (> 15–30 ΔE) behind a clean NAS particle count. WVDJ uses selective Dow ion-exchange resin + electrostatic collection to pull MPC ≤ 8 while leaving synergistic aromatic amine and phenol antioxidants (ASTM D6971 / D4378 ≥ 25% threshold) intact.

ASTM D7843 (MPC)Antioxidant-Safe Resin
03
≤ 100 ppm / NAS 5–6

Sample Tank Bottoms & Respect Fluid Limits

Mid-tank lab bottles often read 50 ppm while hidden bottom water sits near the purifier suction port — always sample from the active bottom drain (never stagnant sight-glass dead legs) before sizing. Benchmark targets for ISO VG 32/46 turbine oil: ≤ 100 ppm water (ASTM D6304 / GB/T 7600), NAS 5–6 (ISO ≤ −/16/13), demulsibility ≤ 30 min at 54°C (GB/T 7305), and stable acid number ≤ 0.2–0.35 mgKOH/g (ASTM D664).

Bottom-Drain CheckISO VG 32 / 46 Benchmarks
ENGINEERING & BUYING FAQ

Turbine Oil Purification & Equipment FAQ

Technical answers for power plant maintenance teams, rotating-equipment reliability engineers, and industrial buyers comparing coalescing separation, ion-exchange varnish control, vacuum dehydration, and lab oil benchmarks.

Should I choose a WJJ coalescing turbine oil purifier or a WZJC vacuum turbine oil filter machine for water removal?

Choose the heating-free WJJ coalescing balanced-charge unit (0.9–7.6 kW, 600–18,000 LPH) when steam-seal or cooler leaks introduce heavy free and emulsified water (< 10% inlet) into demulsible 32# or 46# turbine oil — it separates bulk water faster than vacuum evaporation, cuts outlet water to ≤ 100 ppm, and holds < NAS 5 cleanliness. Choose the WZJC vacuum filter machine (−0.06 to −0.09 MPa, 21–81 kW) when you specifically require vacuum air/gas stripping or sub-100 ppm (≤ 50 ppm) dissolved-moisture removal.

Why cannot standard 3-micron filters, centrifuges, or vacuum purifiers remove turbine oil varnish?

During turbine operation at 40–60°C, polar oxidation byproducts remain dissolved in solution, and nascent colloids sit in the 0.02–0.5 μm sub-micron range. Conventional 3–10 μm mechanical cartridges, centrifugal separators, and heater-type vacuum purifiers cannot capture dissolved varnish molecules or sub-micron gels, causing cartridge blinding while MPC rises. Removing both soluble and suspended varnish requires selective Dow ion-exchange resin paired with electrostatic collection (WVDJ).

What is the moisture boundary between WVDJ (3-in-1) and dry-only WVD varnish removal units?

Dry electrostatic-resin WVD units have zero dewatering capability: they strictly require dry oil (≤ 100 ppm operating limit, ceiling < 500 ppm with zero free water settled at the tank bottom), otherwise water saturates the resin and triggers electrostatic leakage-current shutdowns. Whenever turbine moisture exceeds 100 ppm (up to < 10%) or water ingress coexists with varnish risk, specify WVDJ-20, which adds a full-synthetic coalescing-separator stage to maintain ≤ 100 ppm water alongside MPC ≤ 8.

Does turbine oil purification strip aromatic amine or phenol antioxidants from ISO VG 32 / 46 oil?

No. Under ASTM D4378, turbine oil reaches end-of-life when primary antioxidants drop below 25%. VIFLUTER selects specific imported Dow ion-exchange resins engineered to adsorb polar oxidation degradation products without absorbing hindered-phenol or aromatic-amine antioxidants (RULER ASTM D6971). Meanwhile, WJJ operates completely heating-free (≤ 80°C reservoir temp) and WZJC limits heater flux to ≤ 2 W/cm², protecting oil viscosity and additive stability.

What target water, NAS cleanliness, and MPC metrics should a steam or gas turbine oil system maintain?

Based on power-plant turbine oil standards (GB/T 7596-2017 / ASTM D6304 / ASTM D7843), strict operating targets are ≤ 100 ppm water content (with ≤ 50–100 ppm outlet capability across WZJC/WJJ/WVDJ), particulate cleanliness at NAS 5–6 (ISO ≤ −/16/13; operating ceiling ≤ NAS 8), MPC ΔE ≤ 15 (preferred target ≤ 8; > 30 critical), demulsibility ≤ 30 min at 54°C, and acid number ≤ 0.2–0.35 mgKOH/g.

How do I size the flow rate (LPH or L/min) for a turbine lube reservoir?

For water and particle control in 6–20 m³ steam or gas turbine reservoirs, typical plant builds use WJJ-50 (3,000 LPH / 50 L/min) or WJJ-100 (6,000 LPH / 100 L/min; e.g., two WJJ-100 skids on a 20 m³ GE combined-cycle tank), with custom WJJ models up to 18,000 LPH (300 L/min). For continuous online varnish removal, the WVDJ-20 (20 L/min / 1,200 LPH) is sized for reservoirs up to 80,000 L alongside proper suction/return spacing to prevent short-circuiting.

Why can NAS cleanliness look normal while my bearing pad temperatures keep fluctuating or MPC exceeds 15?

Optical particle counters count solid particles ≥ 4 μm(c), whereas dissolved varnish precursors and early sub-micron gels (< 0.5 μm) remain invisible to particle counting and coat hot thrust-bearing pads as insulating films — driving temperatures to 105–120°C or causing hydraulic servo-valve stiction. Note also the reverse trap: heavy bottom-tank sludge stirred up during initial kidney-loop startup can temporarily raise NAS counts before both NAS and pad temperatures stabilize.

Can VIFLUTER turbine oil purification systems run online in kidney-loop mode without shutting down the turbine?

Yes. WJJ, WVDJ, and WZJC all operate in an independent off-line (kidney-loop) bypass circuit plumbed to the reservoir drain/return ports, leaving main turbine lube pressure and flow completely untouched. Integrated float-level, lid-interlock, leakage-current, overpressure, and phase-protection sensors allow safe unattended 24/7 operation (500+ hours continuous runtime on WJJ) and gradual online re-dissolution of baked varnish without halting generation.

Are explosion-proof (Ex d IIC) and 380V–480V (50Hz / 60Hz) power options available for turbine decks?

Yes. The WVDJ-20-IIC is rated IP56 with Ex d IIC explosion-proof enclosures for hazardous gas-turbine and petrochemical compressor areas, and WJJ / WZJC units can also be custom-built with Ex-proof cabinets, enclosed weatherproof housings (BF/BY), and factory-matched 380V 50Hz/60Hz, 400V/415V 50Hz, or 440V/480V 60Hz power wiring. Standard systems use Viton/NBR seals engineered for petroleum turbine oils up to 80°C and ≤ 220 cSt.

How often should turbine oil purifier cartridges and DICR ion-exchange resin be replaced?

On medium-sized turbine and compressor reservoirs, DICR ion-exchange resin cartridges typically require replacement roughly once per year depending on oxidation load, while WJJ balanced-charge coagulation traps sub-micron sludge efficiently so downstream elements last longer between pressure-differential alarms. Never pull sample bottles solely from stagnant level-gauge dead legs — always verify moisture at the active bottom drain so unexpected free water never saturates resin or cartridges early.